Hi Fernando!

I tested a capacitor of 10µF on 3v3, but it's same.

Now it worked with esplink waiting for you to make new Ferduino board.

Hi Fernando !

installed the module DS3231 as you advised me and it works well, but my wiznet chips work very bad even with 5v by USB.

I have ESP and i buy a logic level converter quickly.

I understand what you say but I do not power the card with the power plug but directly on the + 5v

When use the I2c scan i read that on monitor with jumpers on 2-3:

Hi Fernando, it is the + 5v general card and not the 7v-9v power supply which touched the 12v very briefly. Now the RTC Ds1307 no longer responds even after replacing the integrated circuit. Did you get an idea, or my ferduino board died? Best regards ! Logs with ethernet off : Time: 27:85:85 Free m...

HI!

You were right, but after unplugging the + 5v wire of my Ferduino, he briefly touched the 12v and my Ferduino flashed!

I managed to restart it but the time and date is incoherent and even after tuning I changed the DS1307 IC but still the same

Do you have a new and good idea?

Hi, thank you for your reponse, but i have an IBM serveur power supply and with your old code on JOY REEF it worked well At the start up, it's connected and after failed: Controller IP: 192.168.0.103 Attempting MQTT connection... Connected! Command: Aurelien/*******/topic/command Free memory: 3074 F...

i was making too many changes on your code for adapt to my installation.

i restart to your original code and it's ok now. but sometimes the "webcontrol" website say me "Your controller is not responding".

Hello Fernando, it's been a long time since I came. You have done a good job since and I congratulate you! I have just updated my Ferduino mega but I have a problem with ethernet yet I have: Const byte SD_CARD = 0; Const byte ETHER_CARD = 1; Const byte RFM = 2; Const byte ChipSelect_SD = 5; Const by...

Hi Fernando

It's very interesting


Good work

Hi everyone !!

I have update my Ferduino Mega !!

it's great and everything works fine for me !

VERY GOOD JOB FERNANDO AND DANILO

Thank You

Hi !

THANK YOU Danilo and Fernando.

HI! Fernando Ruben want use an optical, not an ultrasound sensor !! it's optical with an infrared emiteur when the capteur is in the water, the infrared stream is not reflected and the phototransistor is open, same as this sensor : http://www.aliexpress.com/item/ESM-PE21-Water-dispenser-infrared-wat...

Hi Fernando

It's very good

Hi everyone

It might be interesting that we can specify an email address in Joy Reef to send an email when there is an alarm on the Ferduino.

What do you think?

is this possible?

Hi Fernando I cleaned up the code and found the right adjustment for delays, delays after the "open channel" must be 50 to not make any mistakes. Now the probes of PH and ORP is working perfectly with new stamps "EZO". Thank you Fernando. :-bd //----------------------------------...

yes I learn so much and before you ask I always tried several times but I lack connaissnce in coding.


great it works well now, I'm going to like ph2 and orp.

Thank you

ok now i understand "sensorstring".

ok no error, but always ph tank on screen 66.92

Hi! i receives that: Debug pH 1: 7.194 Debug pH 2: Debug pH 3: Debug pH 4: Debug pH 6: 7.193 Debug pH 7: 7.189 With this code : //------------------------------------- Leitura dos stamps void parametros() { int i; do{ Open_channel(ph1); Serial3.print("R"); Serial3.print('\r'); delay(1000);...

What you can learn with this results? i don't know, it make an error when it's connected, maybe You have commented the fucntions for pH2, ORP and EC in "void iniciar_stamps()"? no i don't , why ? there is error of other circuits on my debug ? i comment now the other circuits. With other c...